De Pan

I have a holding tank gauge with sender unit for some years now, but have never enjoyed removing the tank sender unit for a clean from time to time. Even when the unit is especially designed for black water, it would eventually clog up and need to be cleaned. My aft holding tank was easily accessible, so I decided to put a view port in so as to "see" the level of the tank. You can view the old sender unit here at WEMAUSA. It is the one on the right.
First, I had to design my window and decided for simplicity sake, to use a beckson hatch with a clear screw lid. These have a "O" rind for sealing. To this I mounted it on a half inch piece of ply cut to shape and given 3-4 coats of clear epoxy. Screws were mounted so as not to protrude through the other side. I also didn't want screws to go through into the holding tank and the mounting wooden plate adds some stiffness to the tank. Why wood instead of GRP? I like the idea of being able to reverse anything I do and the wooden base plate would (no pun intended) be easier to cut off.
After removing the sender unit, which was now showing signs of corrosion, I had to remove the screw in adaptor. This had a "C" shaped backing plate, so I lassoed it with a cable tie before undoing the last screw which held it there. I was then able to remove the backing plate with some ease.






I marked out the location of the new base plate, takeing out the old hole. But it was somewhat off centre, so to help with the hole saw, I screwed on a scape piece of wood and held it in place with screws through the piece of GRP that was going to be discarded.






To the right you can see how easy it is to drill a new hole where an old hole already exists.










Next, I sanded the paint off with a Rolok sanding disk.










The back of the backing plate was also sanded. Then I mixed up some epoxy with a silica type "Glue" additive to give a peanut butter viscosity. This was applied to the tank and then the backing plate pressed into the mix. Some squeezed out to the inside and I was able to get this before it fell into the tank. (wearing rubber gloves). The out side was smooth filleted with just a finger and left to harden overnight.




Finally the beckson hatch was bedded with 3M 4200 to the base plate.
And the finished inspection/view hatch to the left. It helps to shine a small flashlight up to one side of the clear hatch to get a better view of the level. Plus, now if I want to, I can put a hose in the tank to give it a wash out from time to time.

More work to my holding tanks! I alluded to some of the benefits of using polyethylene hose for sanitation hose and you can read about it here.
 The first thing I did was remove the input hose and fitting, to the holding tank which was located on the side of the tank. Last year, I had relocated the tank air vent to the top and did a temporary block off, of the old side air vent. You can read about that here. That was located just above and to the side of this fitting seen to the left. I used a Dremel and hacksaw to make the cut of the bronze fitting.
 I prepped the area to get ready to epoxy glue on a cover over the old fittings. Old paint removed and each opening stuffed with toilet paper so that the glue would not full into the tank. The glue is made from two pot epoxy (slow set) with silica powder/binder added until you get the consistency of thick peanut butter.
 To the left is the finished fibreglass plate epoxied to the tank. This year I decided to use some off cuts of fibreglass which are cut out when the boats are removed from the molds. Typically, they are window cutouts and hatch cutouts which are then discarded. You local fibreglass boat builder will have plenty of these to give away.


In preparation for the top fitting, I found the best location; drilled my hole for the polyethylene through hole; and then sanded the area for gluing the fibreglass plate to the tank.








To the left is the finished fitting. You might notice that the black hose it is attached to is polyethylene pipe.
Polyethylene pipe is NOT as flexible as sanitation hose, so you may have to use elbows etc to get it to go where you want to. You can also use boiling water to get a little more curve from the pipe.







To the right you can see the 25mm polyethylene pipe running down and through the wall where it goes to the macerator pump. The bigger 38mm (inch and a half) pipe runs from the bottom of the tank to the "Y" valve and then the polyethylene pipe continues on to the pump out pump. A diaphragm pump with joker valves each end.
Now the outflow is of poor design and should never come from the bottom of the tank, other than a drop down pipe inside the tank, from the top. This is due to the fact that effluent is always in the outflow pipe which leads to permeation  I'm using polyethylene pipe from the bottom of the tank and feel confident, there will be no permeation.

Above you can see I used barrel nuts. This makes presenting pipes up to the fittings real easy. In this case I didn't need to use them, but I had bought them with me, so decided to use them.
To the left you can see the macerator pump with barrel nut fittings at both the inlet and outlet. The outlet has a PVC type which was fitted some time ago. On the other side of the barrel nut, I have a joker valve inside the other half of the PVC barrel nut and then a valve. This is because it is pumping up hill and one day I may need to service.
I have now added a polyethylene barrel nut at the inlet side. Also, but not shown, is a threaded pipe (at the inlet side before the barrel nut), which goes to a valve, before joining up with the 38mm pipe from the toilet bowel. IF the pump needs servicing, I just
turn off the valves at either side of the pump; undo the barrel nuts (usually by hand); disconnect power; and pull the pump out. I have a few "boat towels" to mop up the small amount of fluid that will spill.
And let me say, the area smells so much better already. I might even replace the deck pump out hose ( which goes to the "Y" valve. But my wife says, that is just looking for work. Maybe if I get bored sailing?
Listening to "Just Waiting on a Friend" by the Rolling Stones.